1 Press the [SYSTEM] button.
The LED of the [SYSTEM] button will light and the buttons controlling Setup parameters will blink.
2 Press the button which corresponds to the Setup parameter you want to edit.
For details about each Setup parameter, refer to “Setup parameters”.
3 Press a corresponding key to select a parameter.
The seven keys on the left correspond to the parameters (0 to 6).
The V-1~V-3/C-1~C-3 LEDs show the parameter currently selected.
Examples
Parameter “0” | Parameter “2” | Parameter “6” |
|
|
|
4 To configure another Setup parameter, repeat steps 2 and 3.
5 To save the settings, press the [SYSTEM] button.
The buttons stop blinking and the M-solo returns to normal mode.
Master tune
Adjusts the master tuning frequency.
Instrument Type | All |
Corresponding button | [TRANSPOSE] |
Parameter | 0 (434), 1 (436), 2 (438), 3 (440), 4 (442), 5 (444), 6 (446) |
Factory setting | 3 (440) |
Adjusts the Key Click level of the Virtual Multi-Contacts (VMC). A smaller number results in a softer and shorter Key Click. A larger number results in a louder and longer Key Click.
Instrument Type | B-3, Vx, Farf, Ace |
Corresponding button | [LESLIE BYPASS] |
Parameter | 0 (off), 1 (soft) to 6 (loud) |
Factory setting | 3 |
Adjusts the level of Leakage tones.
Instrument Type | B-3 |
Corresponding button | [LESLIE STOP] |
Parameter | 0 (off), 1 (soft) to 6 (loud) |
Factory setting | 3 |
VMC depth
Adjusts the contact time of all the Virtual Multi-Contacts (VMC). If this parameter is set to 0 (off), the Virtual Multi-Contacts are disabled all harmonics will sound when a key is depressed.
Instrument Type | B-3 |
Corresponding button | [LESLIE FAST] |
Parameter | 0 (off), 1 (short) to 6 (long) |
Factory setting | 3 |
MIDI receiving channel
Selects a channel to receive MIDI messages.
Corresponding button | [PERCUSSION ON] |
Parameter | 0 (do not receive), 1 (1ch) to 6 (6ch) |
Factory setting | 1 (1ch) |
MIDI transmitting channel
Selects a channel to transmit MIDI messages.
Corresponding button | [PERCUSSION SOFT] |
Parameter | 0 (do not transmit), 1 (1ch) to 6 (6ch) |
Factory setting | 1 (1ch) |
Local control
Selects whether to allow the keyboard to play the internal sounds of the M-solo.
Corresponding button | [PERCUSSION FAST] |
Parameter | 0 (off), 1 (on) |
Factory setting | 1 (on) |
Generic control
Selects whether to transmit MIDI Control Changes from the M-solo.
If this parameter is set to 0 (off), the M-solo will transmit all Control Change messages.
When set to 1 (on), all control change signals except those for Expression and Damper are blocked. Select 1 (on) if you are playing a typical MIDI instrument in combination with the M-solo.
Corresponding button | [PERCUSSION THIRD] |
Parameter | 0 (off), 1 (on) |
Factory setting | 0 (off) |
Enables/disables the AUTO POWER OFF function. If this parameter is set to 1 (enable), the M-solo will automatically turn “OFF” after 30 minutes if no keys, buttons or knobs are used.
Corresponding button | [VIBRATO & CHORUS ON] |
Parameter | 0 (disable), 1 (enable) |
Factory setting | 1 (enable) |
Selects the operating direction of the Drawbars. If this parameter is set to 1 (reverse), moving a Drawbar forward will decrease a value and moving a Drawbar back will increase it.
Instrument Type | Ens, Syn |
Corresponding button | [CHORUS/OVERDRIVE ON] |
Parameter | 0 (normal), 1 (reverse) |
Factory setting | 0 (normal) |
Determines the function of the Foot Switch connected to the [LESLIE FAST] jack.
Corresponding button | [DELAY/REVERB ON] |
Parameter | 0 (Leslie effect FAST mode ON/OFF) 1 (Sustained note) |
Factory setting | 0 (Leslie effect FAST mode ON/OFF) |
Controls the volume when Expression is set at minimum.
Corresponding button | [PATCH 1] |
Parameter | 0 (pianissimo) 1 (OFF) |
Factory setting | 0 (pianissimo) |